RoboCam F12 Guia de Instalação descarregar pdf (Página 2)

DC/IN

NET

RoboCam

NAT Router

/Access Point

Ethernet CablePower Adapter

1. Connect the power adapter.

2. Connect the Ethernet cable to the NAT/Router which is connected to

the internet.

3. The IP camera will get IP address from the NAT/Router (with DHCP

enabled) automatically and connect to internet. Check if the red LED of IP

camera is always on. If it’s blinking, please check step 1 and step 2 again.

Internet

C.4

2 3

You can drag the camera on the “Auto Search” area to the “Camera List” area.

You could also add new item on the “Camera List” area by “Camera List”

→“New Camera” →Key in camera ID and Password.

Please make sure the Ethernet cable is connected to the IP Cam !

A B C.1

A. Right click camera on the “Auto Search” area and click “Web Conﬁgure”.

B. Key in the admin account and password to enter the web conﬁguration page.

Click “Network\WiFi Security” of the conﬁguration menu.

C. Four steps to setup the wireless connection:

C.1 Click the “WiFi Scan” button, all the available wireless AP will

be listed in 10 seconds.

The default admin account is “admin”, and no password.

WiFi Security Settings

3.1

WPA(2)-PSK(WPA personal)None WEP

Enable WiFi function

Disable WiFi function

SSID

Security mode

WEP Encryption

WPA Encryption

WPA-PSK Key

WEP Key

Save&Apply

WiFi scan

IP address WiFi test

admin

Yes

Username(U):

Password(P):

Remember my password(R)

Cancel

Connect to 10.0.0.198

C.2 C.3

C.4. If the “WiFi test” succeeded, remove the Ethernet cable from the

IP camera to start the wireless connection.

Please do not remove the Ethernet cable during WiFi test.

The blue LED and red LED will be always on after wireless connection is successful.

WiFi Security Settings

Enable WiFi function

SSID

Security mode

WEP Encryption

WPA Encryption

WPA-PSK Key

WEP Key

Disable WiFi function

Save&Apply

IP address

WiFi test

WPA(2)-PSK(WPA personal)

None

TEST

12345678

WEP

C.2 Choose the wireless AP and key in the encryption key.

C.3 Click “WiFi test” button and wait for 20~40 seconds to verify if the

encryption key is correct. If “WiFi test” failed, check “encryption key”.

If scanning failed, please check the antenna or AP.

TEST 54Mbps WPA

54Mbps WPA

NAS

Example

Test1

Test2

Test3

3.2

3.3

You can download the app that suits your smart phone:

"mEZviewerFree" – Free iPhone app.

"mEZviewer" - Free Android app.

"mEZViewerFull" – Paid iPhone app (+push notiﬁcations +SD Playback)

"mEZViewerHD" – Free iPad app

"mEZViewerHDFull" – Paid iPad app (+push notiﬁcations +SD Playback)

Then you could easily add RoboCams by entering the Cam ID & password

FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device ,pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential

installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Move the equipment away from the receiver-Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/television technician for additional suggestions You are cautioned that any change or modiﬁcations to the device not expressly approve by the party responsible for compliance could void Your authority to operate such device.

This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation

Mobile Device Usage, Radiation Exposure Statement: This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.

FCC Caution: Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

WiFi scan

DC/IN

NET

Ethernet

Cable

Plug&View

Camera List

Auto Search

001001001

001001002

001001003

001001004

Auto Search

001001001

001001002

001001003

001001004

Auto search

001001001

001001002

001001003

001001004

Auto Search

001001001

001001002

001001003

001001004

001001001

Camera List

PC software could be found on http://myrobocam.com/plugview.zip or under downloads.

1. Remove the Ethernet cable from the camera.

2. Press the WPS button on the NAT/Router.

3. Press the WPS button on the RoboCam.

4. The blue LED on the RoboCam will start blinking along with other LEDs.

If the blue LED stops blinking and stays on for one minute, the wireless network

is connected successfully.

1. Execute the installed Plug&View software on the desktop or from “Start→

Programs→Plug&View→Plug&View”.

2. The “Auto Search” will display the IP camera in the local network.

3. Double click the camera and key in the password on the ID/password card to

see the video.

If your router has a WPS button

If the router doesnʼt have a WPS button

If your router doesnʼt have a WPS button

DC/IN

NET

1 2 4

Step 1

Step 4-2-1

Step 2

Step 4-2-2

Step 4-1

Step 3

Connecting RoboCam [WiFi]

iPhone/iPad/Android Apps

Once your Robocams are online, start the app and press the ‘+’ sign under Camera List, simply give the

Robocam a name and type in the ID and Password as per the card [or as per your new password if you

changed it], then hit ‘Done’ , you’ll get a message conﬁrming that your camera was added successfully and

you’ll ﬁnd it under the Camera list, you could touch the camera icon to access live, as for settings and SD

Playback you need to press the blue arrow to the right side of the camera icon.

Optionally, if you’re on the same WiFi range as the cameras for the moment, you could perform (Local

Search) in this case the search will ﬁnd the Cam ID for you automatically.

Step 3-1

PC Software

Connecting RoboCam [Wired]

Auto Search

001001001

001001002

001001003

001001004

Web Configure

Adding Robocams to Apps

1 2

RoboCamRoboCam 1
Internet 2

Comentários a estes Manuais

Sem comentários

RoboCam F12 Guia de Instalação Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Câmaras de segurança RoboCam F12